![]() In addition to the spacious, stormworthy, and simple design, the X-Mid Pro boasts the highest quality. The X-Mid Pro 1 also packs smaller than any other 1P DCF tent at just 4″ x 12″ and thanks to the absence of poles and struts it packs short enough to store horizontally in your pack. That includes an ultra simple 4 stake pitch, magnetic door toggles for one handed operation, doorways that aren’t blocked by poles, large vestibules that put the main area beside the doorway instead of blocking it, a tensioned floor that lies taut and wrinkle free, one handed operating zippers, and dual interior pockets. The X-Mid design was formed in tough real world conditions where you need a shelter that just works and this elegant simplicity continues in the X-Mid Pro 1. What hasn’t been overlooked is the user friendliness and simplicity that the X-Mid tents are known for. Additionally, X-Mid Pro 1 features ultra strong and highly waterproof Dyneema ® composite fabric, dual protected doorways that keep rain off the floor even when open, an abrasion resistant woven floor, and guyout points for up to 12 stakes around the base plus peak guylines and side panel guylines can be attached for stormy conditions. Other features found in the X-Mid Pro 1 – but otherwise unheard of at the 1 lb mark – are peak vents (important to minimize condensation) and zippered doorways (blocks drafts, increases structural integrity). Unlike other tents near the 1 pound mark, the X-Mid Pro 1 doesn’t trim away the lower part of the fly for weight savings but instead has a full coverage fly to block drafts and rain splatter while also having the option of raising it higher. More than just a spacious tent, the X-Mid Pro 1 provides a robust shelter for harsh conditions. The generous 90″ floor length combined with steep end walls provides best in class useable length (suitable for hikers up to 6’8″), while the 32″ floor width easily accommodates the widest pads with room to spare. It provides a spacious interior with more headroom, shoulder room, and interior volume than almost any other 1P tent. Until the X-Mid Pro 1, if you wanted a 1 person tent at the 1 lb mark, you had to settle for something cramped or lacking in weather protection. The X-Mid Pro 1 changes that. It combines our maximally weight efficient X-Mid geometry with Dyneema ® composite fabrics (DCF) to create one of the most spacious, simple, and stormworthy 1 person tents on the market – and yet weighs a mere 1 pound (16 oz / 465 g). Once fully bonded, Flex Tape cannot be repositioned.įlex Tape adhesives may resist bonding to some plasticized or waterproof materials, siliconized, greasy, oily, dirty, or porous surfaces.Ĭertain fabrics such as canvas, nylon, polyester, synthetics, cotton and some other materials may need up to 24 hours to reach maximum hold.The X-Mid TM Pro 1 is the ideal tent for the ultralight backpacker. Continued firm pressure will help increase adhesion. Not intended for high pressure applications, such as garden hoses or engine repairs.įor maximum adhesion on porous surfaces, using a standard blow dryer will help the adhesives bond with the surface.įlex Tape’s bond will increase with time and pressure. May cause damage to the surface if removed. May not adhere to certain surfaces such as siliconized or water-repellent materials. Continue pressing firmly for 1 minute or longer to allow Flex Tapes adhesive to completely bond to the surface being sealed. These are areas are where water could seep through and create a leak.ĥ. Make sure all water, air pockets, creases and folds have been completely removed. Press firmly using your fingers, squeegee, credit card, roller and continue pressing firmly starting at the center and working towards edges.Ĥ. For best results, apply Flex tape to both sides of the repair.ģ. Once applied Flex Tape cannot be repositioned. Remove the liner and apply the Flex Tape firmly over the area being sealed. You can also round the corners of the patch to help prevent the corners from lifting.Ģ. Keep the liner on and cut Flex tape to create a patch larger than the area being repaired. Only use on smooth, clean non-porous surfaces and applied at room temperature.ġ. How To Use Flex Tape on Wet Surfaces or Underwaterįor best results, when applying on wet surfaces or underwater, make sure the area being sealed is clean and free of any grease, oil, dirt, debris or algae. *Flex Tape is a temporary, emergency repair and is not meant to be a permanent fix. Using your fingers, plastic squeegee or roller, press down firmly and remove any air pockets. ![]() Apply tape to a clean surface and press down firmly.Ĥ. Make sure to use a high quality utility knife with disposable blades or a razor blade when cutting.Ģ. Leave backing on tape and cut to desired dimension.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |